Видео

My car does not have thr little notches for the ends of the aerowing. Does anyone know where i can find one or know of alternatives?

How you remember were all this stuff go

love the GTA but love the GTA TURBO more

if my original Home button doesnt work, with this video and replacement of the shell, will it work again?

Excellent video! went through it step by step and everything went smoothly! thanks!

Thank you for this magnificent tutorial... best wishes!!!

Thanks for the response on my 1st question!! One more question: so i purchased the all aluminum 3 row rad; and when moving my transmission fittings over,.....they are too big. Wont screw in. So does the transmission lines go straight into the aluminum rad?? Or do i need to hunt for smaller fittings??

I don't even know if you'll reply to this but ive got an 88 bronco, and my alternator recently caught on fire. I've been trying to remove the bottom bolt and I've gotten it almost out but now it'll just spin in the hole. I don't know if I just need to wiggle the alternator a little bit while im losening it or what but some advice would be appreciated.

I just finished the repair by watching this tutorial, and I had a few problems, so for anyone that is going to try this, keep in mind that this is never going to take 12 minutes. For me, it took me 4 hours, but I spent 1 dealing with a stripped screw. I would have preferred if you didn't put cuts on the more difficult part, like at 2:56 and at 9:24 when I got stuck because I didn't see what you did. Also, I don't know what the hell you did during the cut at 1:45 but you broke the R button and never mentioned it during the video 0.o

One of the screws in the back housing doesn't want to move and I think I've already damaged the screw

Hi!! Thank you so much for the video. I really want to change the whole shell of my 3ds but I’m so scared that I’m gonna break the console in some way. The only thing that I ever did slightly similar to this is changing the shells in Nintendo switch joycons (and actually it was super easy for me). Do you think I’ll be able to do this with my 3ds without ruining it?

Im old, but brand new to engine work. I bought a 1987 F150 and want to trick it up a bit. Your videos are great. For the EGR replacement, what was the name of the valve pump? Thanks.

Very helpful! Going to be my project for this weekend

Is the link for Auto spindle socket part # for a 2 3/8" or 2 1/2"? Looks like you where using a 2 1/2" in your video.

I appreciate all of these videos as I have a 96 Bronco! Any chance you might be able to look into fixing the wiring for the brake lights / turn signals? :)

I don't think I've ever seen a device with so many flex connectors. Props to Nintendo for designing a repairable device rather than one packed with glue.

I had to go with electric fans on my LS swapped 85 Cutlass cuz of clearance issues. I thought i was lucky at the time to score a complete rad Shroud with dual fan setup for $100 cdn. It was new out of box. By time i added relays fuses and fusebox is was over 200 cdn. I went to the trouble of programming ECU for two come on temps. i think hi speed fan came on at 185F and additional low speed fan came on at 195. TURNS out unless you are just idling around in stop n go traffic the fans almost never even came on. ANY amt of air from just driving cooled engine well enough w/o ANY fans. if i had to do it again i would turn on low speed fan first as it was half the noise and probly good enough for most situations.

your videos are all so informative and easy to follow. I've got a 96 bronco and I've been following all your videos to restore it as well! keep up the amazing work you do

excellent as usual. So happy to have found your site, I have a Bronco 90 eddy bauer and I have a lot of difficulty finding videos of this quality. I need to change my gas pump, your recommendations are more than welcome. Thank you

Thanks for reminding about the double cardan. I need to service that bugger. I replaced the joints and figured I'd do that later.... 6 years later. Haha

Bro these videos have been a huge help to me while restoring my 96 bronco. The quality is top notch, simple explanations and clear shots of what you’re doing. Very much appreciated. I do have a question: did you use the same u-joint for all 3 spots in the driveshaft? The one listed in the description (x3)?

Great video....my deadpod will remain dead however...😢

Preschool classroom or classroom circle time activity.

Independence Day in the classroom.

at home or in school.

where do you get the lil black rubber bumper strips on the triggers?

I love watching your videos, I get courage from them to do some small repairs on my own bronco, can you do a pov drive test any time? thank you so much!

This video along with the commentary below was of significant value to me (95 F150 4x4); thus, thnxs dude. Note: I am surprised by the number of ostensibly good shops that don't want to mess with the camber bushing (even if you supply same) and just want to set the toe and send you down the road!

Do you have a good recommendation for replacement trim screws and trim and door panel clips for the bronco?

What if my region doesn’t show up 😅😅

I love how gentle you were with it almos like it was your child

Hi! Does a slight crack in the chin bezel plate affect the screen or LCD?

Like surgery lol

your truck is looking great for a 34 year old rig.

I've destroyed 2 screens trying to roll this godamned flat, whoever designed this deserves the coldest gulag

Awesome job! How is your truck driving now after this repair?

Very informative video about the driveshaft U-Joint repair

Non il a tout cassé 😭😭😭😭😭😭

My shaft looks different than yours. XD But really it does, mine doesn’t have that boot on it.

Flawless 🔥🔥🔥 NEW Subscriber!

This repair took care of my driveline vibration. Just be extra cautious when installing the Double Cardan onto the centering shaft.

Awesome! Thank you for this!

I doesn't surprise me the most viewed part of this video is at 12:55 because I spent like 3 hours trying to put that faceplate in place and it was literally impossible, I tried to place my own plate and it was like butter, but the new one I bought is slightly different but I don't know where are the differences, I ordered a refund and bought a new one, 2nd try next week.

Trying to do 6:16 is causing me immense physical and mental pain.

its money

I was planning on doing that but nvm i guess

Wonderful guide near perfect!! So somehow I got my top screen static looking and not looking good it was perfect beforehand I wanted to fix the old hinge and I got to the end 😭 halp pls what can be causing top screen problems (did not cut the old screen protector off kept it the same)

Hi, you did a video on how to repair sticky 3ds buttons but you didn't show how to do it on the power button which is my current problem, do you know how? I have no idea how else I am supposed to get it fixed :/

Did one work better than the other? I want to do the same to my bronco. Just curious which one you thought worked better. The foam or the shiny one for sound deadening.

Guys can i ask you something? I have a nintendo ds fat that i wanted to gift to a friend but the card reader for ds games is a bit faulty and wouldn't read the cartridges well. Are the card readers the same for ds lite and ds fat? (Im Sorry if my English may sound a bit scuffed in advance)